(1) clean the window glass

我们知道，车窗玻璃由于长时间露在外面带有的灰尘可能较多，而车膜在灰尘较多的地方粘合度较差，所以贴膜之前我们要做的一件事是清洁车窗表面。建议大家用湿抹布完全的清洁一遍，特别要注意的是对车窗密封条的清理，密封条里可能含有沙石，灰尘等，如果不清理干净很可能会划伤车膜，好使用吹风枪，刮板等清洁干净。

We know that the window glass may have more dust when exposed to the outside for a long time, and the adhesion of the film is poor at the place with more dust. Therefore, one thing we need to do before applying the film is to clean the window surface. It is recommended that you clean the window sealing strip completely with a wet rag. Special attention should be paid to the cleaning of the sealing strip. The sealing strip may contain sand, stone, dust, etc. if it is not cleaned, it is likely to scratch the car film. It is better to clean it with a blower gun and a scraper.

2外部定型

(2) external finalization

清洁好车窗之后，我们就开始了贴膜工作，要做的就是定型。我们可以利用清水把车膜粘附在玻璃上，进行外部的定型。如果车窗的弧度比较大，车膜贴上去之后出现了褶皱，这时候千万不能直接撕下来，我们好使用风筒以及刮板对车膜进行定型，以达到车膜和玻璃之间更好的贴合度。

After cleaning the car window, we started to apply the film. The first thing to do is to set the shape. We can use water to adhere the car film to the glass for external shaping. If the curvature of the window is relatively large and the film is folded after it is pasted, it must not be torn off. We can use the air duct and scraper to shape the film to achieve a better fit between the film and the glass.

3裁膜

(3) film cutting

定型之后，我们要做的是根据车窗玻璃的大小形状，剪掉多余的部分，也就是要对车膜进行细致的裁剪。裁剪时要注意的是车膜顶部需要比车窗顶部略微低几毫米，以防止玻璃在升降过程中出现卷边现象，影响美观和使用效果。

After finalization, what we need to do is to cut off the redundant parts according to the size and shape of the window glass, that is, to carefully cut the car film. When cutting, it should be noted that the top of the film should be a few millimeters lower than the top of the window to prevent the glass from curling during the lifting process, which will affect the appearance and use effect.

4贴膜

4 film

定完型，裁完多余的，我们接下来就可以正式的把车膜贴在车玻璃上了。撕去车膜背面的保护膜，在内侧玻璃和车膜上喷上水，并且用水将车膜与玻璃贴合在一起，仔细修补车膜的边缘处，让它与玻璃边缘更好的结合，防止出现飞边情况。

After setting the model and cutting the surplus, we can formally paste the film on the car glass. Tear off the protective film on the back of the car membrane, spray water on the inner glass and the car membrane, and use water to bond the car membrane with the glass. Carefully repair the edge of the car membrane to better integrate it with the glass edge to prevent flash.

5赶水

(5) drainage

后我们不要忘了对车膜赶水，将撕下来的车膜背面的保护膜喷上水再次贴在车膜上，用刮板刮压车膜表面，使车膜与车窗之间多余的水分被排出，让它的粘合度更加严密。用车膜背面的保护膜可以更好的避免刮板对车膜的损坏。

After that, we should not forget to water the film, spray water on the protective film on the back of the torn film and stick it on the film again, scrape and press the film surface with a scraper, so that the excess water between the film and the window is discharged and the adhesion is more tight. The protective film on the back of the film can better avoid the damage of the scraper to the film.

以上就是为大家介绍的有关济南汽车贴膜的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.tiekemoshe.com/

The above is the detailed introduction of Jinan automobile film. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://www.tiekemoshe.com/